DIY Solar – Soldering Solar Cells
If you are building “solar panels for your home”, one of the most important
things to learn is proper soldering of the solar cells. Building your own solar
power system can be a very fun project, but if you are having trouble
soldering your solar cells then stop right now! When I first started by first
attempt to solder, I failed. I thought to my self, “what am I doing wrong”,
then I discovered the secret to soldering solar cells. Follow the instructions
below for perfectly acceptable soldering techniques.
Cells I use – To start this mini-training series, you need to determine what
type of solar cells to use. My own personal preference is the 3 x 6 inch cells
that are rated at.5 volts each. I found that these are easier to solder and
work with.
Soldering iron – This is one of the trade secrets of the pros, a proper
soldering iron. I have found experimenting with different soldering irons and
different wattage of heat the best solutions is to use a 40 watt iron. Buy a
good heavy-duty iron, I suggest a soldering station with a wipe sponge to
keep your tip clean at all times. The tip I prefer has a slight angle to it and
can be easily replaced. To not use any tip wider than 1/8th inch.
Solder to use – This is a very important step in soldering solar cells, the
proper solder. There are so many different solders on the market that your
head will start to spin wondering which one to use. My rule here, KIS (keep
it simple). Any electronics supply will carry solder made for electronics
projects that will have a low melting point. This is crucial when soldering our
cells.
Soldering flux – It is important that when doing a DIY solar project that you
use proper flux. The purpose of soldering flux is to condition the metal that
we are attaching to, so that the solder will draw or easily attach. Use liquid
flux available in pens designed for electronics.
Heat sink – Here is one of the best steps to follow if you want perfect solder
connections. If you want to have consistent soldered connections, then I
would recommend using a piece of tempered glass. When I build all my solar
cells I use ¼ inch tempered glass. I build all my cells by encapsulating them
on the glass, so this works great for soldering them also.First thing you must do is plug your soldering iron in and let it come to the
proper heat temperature. Next, prepare your tip for use by applying solder
to it and see if it melts easily. The first time you use your iron you must clean
your tip by applying solder then pulling it through your wet sponge, this will
coat your tip with a glaze of solder. Now you are ready to get started.
I start by making sure my glass is perfectly clean by using some type of glass
cleaner. Now take one of your cells face up or the side that faces the sun,
this is your negative side when hooking them up. Having already cut your
tab wires to the proper length we can start to solder them to the cell.
Apply flux to the two silver strips on the solar cell. Here is a little trick to
help make your soldering easier. Use sockets from a socket wrench set to
hold down your cell while applying solder; this keeps it in place while
preventing warping of the cell. Next, lay your tab wire flat against the silver
strip and hold in place using a small flat tip screw driver. Apply a small
amount of solder to your soldering iron; this will be all you need since the
factory tab wires are already coated with solder. Now draw your soldering
tip across the tab wire, you will get the proper feel for this as the solder
melts as you move the iron along the solar cell. Keep doing this until you
have enough cells to do one complete panel.
After soldering all your negative sides of your cells you are ready to start
joining your cells together making your stringers of cells. Turn over one of
the recently soldered solar cells then take another one and slide under the
tab wires and dab each of the 6 silver solder points with flux, and attach the
same way using solder for each of the solder points. Guess what, you have
properly soldered your first solar cells!
What is great about this method is that you are already ahead of most
people who do not know the proper way to solder solar cells. Just remember,
just the right amount and do not leave the heat on to long or you will warp
your cell and possibly damaged it.
Popularity: 11% [?]
Related posts:
Leave a Reply
